Sailboat-Data

Gibert Marine
Gib'Sea 372
Deep draft

To succeed to the Gib'Sea 105 and 106, Gibert Marine calls again the duo Joubert / Nivelt to design the Gib'Sea 372. The hull forms are more traditional with rounder sections and smaller rear forms. This gives to the Gib'Sea 372 a good balance and nice performance in light winds.

We notice also the increasing of the freeboard, due to the elimination of the raised bridge of the 106 and the will to improve interior space. Two sets of accommodations were available Standard resuming the layout of 106 with two aft cabins or Master giving priority to the proprietary aft cabin and toilet compartment.

No more ballasted centerboard version but a shoal draft (1.4m - 4.6ft) version more economical and efficient than the mobile appendage.

See the Gib'Sea 372's specifications on Boat-Specs.com.

Main Features

ShipyardGibert Marine
ModelGib'Sea 372
VersionDeep draft
Sailboat typeCruising monohull
DesignerMichel Joubert
Bernard Nivelt
Building years (first/last)1987 / 1992
Number built116
Predecessor Gib'Sea 105
Regulation1ere cat.
ConstructionFiberglass/polyester, monolithic hull, balsa sandwich deck
UnsinkableNo
TrailerableNo
Appendage typeTrapezoidal keel
Ballast typeCast iron
Rudder bladeSingle rudder on skeg
RudderSingle tiller (helm wheel in option)
Main dimensions
Length over all37.6 ft
Hull length35.8 ft
Waterline length31.6 ft
Beam over all12.0 ft
Waterline beam10.2 ft
Fore freeboard4.3 ft
Middle freeboard3.5 ft
Draft6.1 ft
Mast height49.3 ft
Light displacement13558 lbs
Full load displacement16094 lbs
Ballast4189 lbs
French customs tonnage12.97 Tx

Rig and sails

Rig typeMasthead Sloop
Rig materialMast and boom in Aluminum
Number of rows of spreader2
Spreader angleNeutral (0°)
Sails
Spinnaker typeSymmetrical spinnaker
Upwind sailarea752 ft²
Downwind sailarea1224 ft²
Mainsail area277 ft²
Genoa area475 ft²
Working jib area361 ft²
Jib area223 ft²
Stormsail area75 ft²
Spinnaker area947 ft²

PMainsail hoist measurement (from tack to head)

39.4 ft

EMainsail foot measurement (from tack to clew)

12.8 ft

IFore triangle height (from mast foot to fore stay attachement)

44.3 ft

JFore triangle base (from mast foot to bottom of forestay)

13.1 ft

LLGenoa hoist measurement (from tack to head)

45.3 ft

LPGenoa perpendicular measurement from clew to luff.

22.0 ft

SLSymmetrical spinnaker hoist measurement (from tack to head)

44.6 ft

SMWSymmetrical spinnaker width

26.9 ft

Performance

Wetted surface309 ft²
Transverse section maximum surface15 ft²
Righting moment @ 1°170 lbs/ft
Ballast ratio30.9 %
Upwind sailarea / displacement122.3 ft²/Ton
Downwind sailarea / displacement199.0 ft²/Ton
HN (French rating)21.0

Auxiliary engine

BrandYanmar
Type1 x 3GM
Engine power1 x 27 hp
Fuel capacity21.1 gal
Fuel typeDiesel
Transmission typeShaft-line
Propeller typeTwo-blade propeller

Accommodation

Number of cabin (max./min.)3 / 2
Number of berth (max./min.)8 / 6
Number of shower room1
Fresh water capacity84.5 gal
Headroom max6.5 ft
Headroom kitchen6.2 ft
Headroom shower room6.0 ft
Saloon
Headroom6.1 ft
Chart table dimensions2.7 x 2.5 ft
Table dimensions2.9 x 3.7 x 3.4 ft
Length of berth6.6 ft
Width of berth*2.0 / 2.0 / 2.0 / 2.0 ft
Fore cabin
Headroom6.0 ft
Length of berth6.9 ft
Width of berth*5.2 / 3.9 / 2.6 / 1.3 ft
Aft cabin
Headroom6.0 ft
Length of berth6.6 ft
Width of berth*5.2 / 4.9 / 4.6 / 3.9 ft
Cockpit
Catwalk width1.5 ft
*Widths of the berths are measured from the head and then every 60cm (2ft), corresponding to the elbows, knees and feet.

Based on specification1988

Did you found this specification helpful? Then share it with your friends by clicking the buttons below:

Similar sailboats

SailboatHull lengthFirst built
Yachting France Jouët 1080 (sailboat) Yachting France Jouët 108035.4 ft1983
Bénéteau Idylle 11.50 (sailboat) Bénéteau Idylle 11.5036.4 ft1983
Kirié Feeling 1100 / Elite 37 (sailboat) Kirié Feeling 1100 / Elite 3735.9 ft1982
Bénéteau First 35S5 (sailboat) Bénéteau First 35S534.8 ft1988

An error in the data, an item to add? Feel free to contact us